SMC Electric - Our knowledge is your power.

SMC BLOOD DRIVE

Date Of Event: May 23rd, 2012
Location: SMC 2615 S Jefferson

register now

ROCK ON. GIVE LIFE

Missouri Department of Social Services and SMC need your help to save a life. SMC will be holding a blood drive in our parking lot from 10AM to 2pm. Make sure to stop by and donate life giving blood.

Motion Control Fundamentals

Date Of Event: June 4th, 2012 — June 5th, 2012
Location: SMC Training Center 1616 W. Main Sedalia, Mo

register now

COURSE NUMBER: CCN142 Course COST: $1200

Course Purpose This course is intended to provide you with the skills to configure and program Logix5000 applications specifically for integrated motion control functionality using ladder logic, including both SERCOS and analog motion control technologies.

Building upon the skills gained in the RSLogix 5000Ô Level 3: Project Development (CCP143) course, you will learn how to apply the Logix5000 architecture to a multi-axis motion control system while developing programming skills that incorporate other components in a Logix5000 system, such as adding system modules, sharing tasks between multiple controllers, programming ladder logic, and using digital I/O. Because all Logix5000 products share common features and a common operating system, you will be able to apply the configuring and programming motion control skills you learn in this course to any of the Logix5000 controllers that are capable of motion control.

To register for this or any other Rockwell Automation training course, contact Donna Reid @ SMC (660) 827-5377 or Pete Phillips @ (660) 221-6334.

SLC 500 Processors Maintenance and Troubleshooting Course

Date Of Event: June 5th, 2012 — June 8th, 2012
Location: Joplin Training Center

register now

Course Number: CCPS43
June 5 - June 8, 2012 SMC 923 W. 4th St. Joplin, MO $1975.00/person
RSVP to Suzan at (417) 624-5454
This skill-building course provides you with the necessary practice needed to interpret, isolate, and diagnose common hardware problems related to noise, power, and discrete and analog I/O. In troubleshooting scenarios, you will be introduced to basic ladder logic interpretation, which is applied to diagnostic tasks. You will practice these diagnostic skills by tracing through ladder logic instructions in an RSLogix 500 project. An integrated practice of multiple troubleshooting skills completes the training. Who Should Attend Individuals who are responsible for troubleshooting and maintaining SLC 500 systems using RSLogix 500 software should attend this course.

Logix5000™ Controllers COURSE NUMBER: CCP299

Date Of Event: June 25th, 2012 — June 29th, 2012
Location: Joplin- SMC Training Center

register now

Logix5000™ Controllers COURSE NUMBER: CCP299 Cost $2350
Register Below or contact Suzan at (417) 624-5454
Upon completion of this course you will be able to troubleshoot a previously operational ControlLogix system hardware.
RSLogix 5000 software Practicing a systematic strategy for diagnosing and trouble shooting problems:
Configuration issues Electrical noise Faulty/malfunctioning field devices Controller, I/O or other hardware issues
Performing hands-on exercises All Logix5000 systems use the same control engine; therefore, tasks are similar. You will see applicable references for other systems.
Who Should Attend This course is intended for individuals who need to maintain and troubleshoot a ControlLogix system – but have no current working experience with ControlLogix systems.
Prerequisites To successfully complete this course, the following prerequisites are required:

• Ability to perform basic Microsoft Windows tasks
• Knowledge of basic ladder logic instructions (bit, timer, counter, etc.) through previous training and/or personal experience

Level 4 Motion Control

Date Of Event: August 12th, 2012 — August 21st, 2012
Location: SMC Training Center 1616 W. Main Sedalia, Mo

register now

Course Name: Level 4 motion control Cost: $1875.00

Course Purpose This course is intended to provide you with the skills to configure and program Logix5000 applications specifically for integrated motion control functionality using ladder logic, including both SERCOS and analog motion control technologies.

Building upon the skills gained in the RSLogix 5000Ô Level 3: Project Development (CCP143) course, you will learn how to apply the Logix5000 architecture to a multi-axis motion control system while developing programming skills that incorporate other components in a Logix5000 system, such as adding system modules, sharing tasks between multiple controllers,programming ladder logic, and using digital I/O.

Because all Logix5000 products share common features and a common operating system, you will be able to apply the configuring and programming motion control skills you learn in this course.

To register for this or any other Rockwell Automation training course, contact Donna Reid @ SMC (660) 827-5377 or Pete Phillips @ (660) 221-6334. You can also access course information via the Web at: http://www.smcelectric.com